How to install PVC decorative film?

How to install PVC decorative film?

/in /by

How to install PVC decorative film?

 Substrate adjustment

1. Substrate – Be sure to grind the flat page to a fine and thoroughly touch and insert it thoroughly. If there is oil stains, clean it with solvent.

The temperature of homework is 15 ° C to 20 ° C, and in principle, construction can be carried out at 5 ° C.

 Plane construction

1. The substrate treatment is as described above.

2. Determination of position: The position to be placed first is fixed with leftover materials.

3. Before pasting, peel off the paper by about 10 centimeters, and use a soft cutting blade to gently press the air out from above.

 

4. If there are small bubbles, the blade can be used to puncture them and then the air can be pushed out with a cutting blade. It is best to wrap the cutting blade with a soft and damp cloth to avoid damaging the surface.

Right angle construction

1. Please apply primer to the substrate and dry it thoroughly before smoothing it out

When the flat part is constructed to the right angle part as described above. According to the following figure, the construction can be carried out by gently pressing in the order of the top, or by heating and pressing with an electric hair dryer. At this point, gloves can be worn or a soft cloth can be gently pressed with fingers to achieve good results.

4、 Double right angle construction. The substrate treatment is the same as before.

2. Paste: First, attach A and fold it onto side B, then fold side B onto the quilt and cut off any excess film (note that if the dot printing part of A and B overlaps, it will protrude here. For aesthetic reasons, it is not necessary to fold A to side B).

Construction method for pentagonal and cubic curved surfaces

1. The corners of the substrate should be thoroughly coated with primer (3-4 times), dried, and ground with # 400 sandpaper until smooth and smooth,

2. Use an electric hair dryer to fully heat the corners. When the Polaroid film has appropriate softness, pull it down from the top of Figure 12A and press it down in sequence B’C’D’E ‘.

3. Please pay attention to slowly pulling from the top in the order of Ai B’C’D’E (less than one centimeter at a time), press with your fingers, then move to B “C’D’E and repeat from A to the bottom. Do not be impatient and pull to the bottom at once, which will cause wrinkles and make it difficult to handle.

4. When heating and pulling downwards, it is advisable to extend your fingers deep inside (do not only pull towards the edge; pull and press on one side to achieve good construction results).

 

What is pvc film

What is pvc film ?

/0 Comments/in /by

We may often hear the concept of pvc film in our lives, but what it specifically represents may not be understood by many people, and they still stay in the vague understanding of cling film and plastic film. In fact, pvc products have been widely used in our lives, especially in architectural decoration. Many of the furniture we see are covered with a layer of PV film, which can not only make the appearance of the furniture more beautiful and generous, but also enhance the service life of the furniture.

What is PVC film?

PVC film (polyvinyl chloride film), which is made of polyvinyl chloride resin and other modifiers through calendering or blow molding. Generally, the thickness is 0.08~0.2 mm, some thicker than 0.25 mm are called PVC sheets. Plasticizer, stabilizer, lubricant and other functional processing aids are added to PVC resin, and then rolled into film.

Main components of PVC film:

PVC resin:40%~70%, plasticizer:10%~50%

Stabilizer:1%~10%, filler:1%~30%

Colorant : 1%~10%

Characteristics of PVC film:

PVC film is insoluble in water, alcohol, gasoline, and can swell or dissolve in ether, ketone, chlorinated aliphatic hydrocarbons and aromatic hydrocarbons. At room temperature, it is resistant to concentrated hydrochloric acid, 90% sulfuric acid,  50%-60% nitric acid, and caustic soda solution below 20%.

Properties of PVC film:

Ordinary adhesive film is directly pasted on the surface of the board with glue at room temperature,  after one or two years, the film may fall off easily. The PVC film is attached to the surface of the board at a high temperature of 110 degrees by a special vacuum laminating machine, so it is not easy to fall off.

Although PVC film has excellent quality assurance, some people may say that PVC is after all just a chemical product l, so it is not as good as natural materials, it also  can not eliminate toxicity and odor, and it will inevitably cause damage to our environment. In fact, they are wrong ,because the raw materials for the general production of PVC film are specially refined, and the toxic substances are completely extracted.

Therefore, PVC is completely non-toxic and tasteless, and has no irritation to human skin or respiratory system. For those who are allergic to wood and paint, furniture or kitchen utensils packed with PVC film are extremely  suitable. By using PVC film as a decorative film, people can use a large number of medium-density boards, particle boards, plywood and fiberboards, instead of the wood using to reduce  damage to forests and the environment.

From this perspective, PVC film has made a great contribution to the protection of the ecological environment. The quality of PVC is not inferior to other alternatives, and the cost is cheaper than these materials.

The PVC film industry is developing rapidly all over the world and has broad prospects. Everyone is optimistic about the potential and the benefits to the environment of PVC film .With its excellent and special performance, PVC film proves to the world that its role and status cannot be replaced by any other products. Social development Need it, environmental protection needs it, it is the inevitable trend of civilization progress of our human society.

Qisheng is a professional pvc film manufacturer from China that offer both standard density and customized density pvc film per customer’s requirements. If you are looking for high quality pvc film for your projects, please don’t hesitate to contact [email protected] .

 

 

 

 

How to calculate density of pvc film ?

/0 Comments/in /by

If you’re working with PVC film, it’s important to know how to calculate its density. This will help you determine the best way to use the material and ensure that your project is a success. Here’s a quick guide on how to do it.

PVC film is a versatile and durable material that can be used for a variety of applications

PVC film is a reliable and multi-use material with so many possibilities. It’s no wonder it has become the go-to choice for those looking for an economical and easy way to make their product or project stand out. This versatile and durable material can be used for almost anything, from protecting windows to wrapping around furnishings, decorations, or signs. Plus, it can even be printed on so you can make your projects completely custom! Whether you’re crafting something on your own or stocking up as a business owner, PVC film is the perfect option for flexibility and affordability.

The density of PVC film can be calculated using the following formula: (mass of PVC film / volume of PVC film) x 1000 = density of PVC film in g/cm3

PVC (polyvinyl chloride) film is a type of plastic and is used for a wide variety of purposes, ranging from window frames to packaging. PVC film has a specific density which can be calculated using the relevant formula. The formula takes into consideration the weight and the volume of the PVC and provides an accurate result. The ability to calculate the density of PVC film accurately is important in order to select an appropriate product with the specified characteristics according to the specific application requirements.

The formula used to determine this important value involves dividing the mass of the PVC film by its volume, then multiplying the outcome by 1000 to obtain the density in g/cm3. By understanding this formula and its application, individuals analyzing PVC films can accurately report their properties and make more informed decisions about how they should be used. Determining the final density is fundamental for improving functionality, expanding knowledge, and driving innovation for future vinyl films.

This information can be useful when choosing the right type of PVC film for your project

When it comes to PVC film, the choices available can seem overwhelming. The key to selecting the film that’s best suited for your project is understanding what the various options have to offer and this information is invaluable in making an informed decision. PVC film can be found in a vast range of sizes, finishes, thicknesses and colours so it’s important to have as much knowledge about each type as possible — before committing to one — to ensure you get exactly what you’re looking for. Understanding this data can help make sure you pick the type of PVC film that’s just right for your project and will provide you with great results every time.

Keep in mind that the density of PVC film may vary depending on the manufacturer

When researching a purchase of PVC film, it is important to keep in mind that the density of the product may vary depending on the manufacturer. This variation can significantly alter the performance of the product and could ultimately change the intended use of the PVC film. As such, customers should always consult reviews or do thorough research when selecting a supplier to ensure they are investing in superior quality materials. Understanding variations in density across multiple manufacturers will also help buyers make financially savvy decisions as they select products with optimal weight-to-strength ratios.

Qisheng is a professional pvc film manufacturer from China that offer both standard density and customized density pvc film per customer’s requirements. If you are looking for high quality pvc film for your projects, please don’t hesitate to contact [email protected] .